PAL System Modules

PAL Thermal Mixer, for shaking and heating of well plates.
Only compatible with PAL table mounted.
Temperature range 30-100°C
Mixing 0-2000 rpm

Requires FW 4.1 or higher

Adapter needs to be ordered separately:
PAL3-TM-Adap-ABGene: Adapter for Abgene™ 96 Well 0.8 ml Polypropylene DeepWell™ (Thermo part number AB0765)
PAL3-TM-Adap-EPP: Adapter for Eppendorf® Deepwell plates, standard, 96 wells, conical bottom colorless wells, capacity 1000 µl (Eppendorf part number 0030501209)

Wash Cup Setup, consisting of:

1 pc 2-Channel Volumetric Pump incl. holder and PAL Bus Connection cable
1 pc Wash Cup PEEK
1 pc PFA Transfer tube 1/16" for up to 850 mm
2 pcs Solvent Bottle 1000 ml
2 pcs Solvent Inlet Tubing Kit PFA

Attention: For x-rails longer than 850 mm PAL3-TubeLC/MS-VP-X is required (to be ordered separately)

Requires PAL Series II with FW 4.12 or higher

• For the incubation and agitation of samples
• 6 positions for 20 ml vials
• Temperature range 40 - 200 °C
• Agitation speed 250 - 750 rpm
• Optional adapters for 2 ml or 10 ml vials

Requires firmware version 1.3.0 or higher

• Reads horizontal 1D barcodes
• Two scanners allow identification of vials irrespective of position of the barcode
• Works with 2 ml / 10 ml / 20 ml vials

Requires firmware version 1.3.0 or higher

• For the efficient centrifugation in automated workflows (e.g. protein precipiation, phase separation)
• Control through many Chromatographic Data Systems
• Relative centrifugal force: 2000 x g with centrifuge Combi
• Vial format: 2 ml (4 vials,) 10 ml / 20 ml (2 vials)

Requires firmware versions:

3.1.19.1 or higher for PAL3 Series II
2.5.57.2 or higher for PAL3 series with iMX6 board

PAL Sample Control users need PAL Sample Control SW Version 2.5 or higher

• For efficient mixing (dilution / extraction)
• Standard vial sizes: 2 ml / 10 ml / 20 ml
• 1 additional slot for custom specific vials
• Provides efficient mixing with up to 2000 rpm

Requires firmware version 1.3.0 or higher

• Opens/closes 2, 10, 20 ml screw cap vials without any change of hardware (no adapters required)
• Defined torque guarantees the reproducible and leak-tight closing of headspace vials

requires FW Version 2.4 or higher

For the efficient and accurate addition of larger amounts of liquids

consisting of:

1 pc Dilutor Single
1 pc PAL Bus Connection cable
1 pc Dilutor Tool
1 pc Dilutor Syringe 1 ml
1 pc PFA Transfer Tube 1/16"
1 pc Solvent Bottle 1000 ml
1 pc Solvent Inlet Tubing Kit PFA

Requires firmware version 2.1.0 or higher

For the conditioning of SPME Arrows and SPME Fibers prior to sample enrichment, max. 350 °C

• Position for automated conditioning
• Position for manual pre-conditioning
• Automated purge gas valve
• Manual gas valve for pre-conditioning

Requires firmware version 2.3 or higher

For minimized carryover

cleans syringes of gauges 19 to 26 and supports two different wash solvents (aqueous and organic)

For flow rates up to 40 ml/min.

cleans syringes of gauges 19 to 26 and supports two different wash solvents (aqueous and organic)

PAL System Wash Module for LC/MS Tool
consisting of:

1 pc Wash Module with two wash positions and one waste position

Passive Wash Module for use with LC/MS Tools or Dilutor Tools

Requires FW 2.0.x or higher

Wash Module for large volume injections

consisting of:

2 pcs 100 ml Solvent container (glass) with septum cap
1 pc Waste Port with tubing olive to connect waste bottle

PAL System Tray Holder for the storage of:

3 pcs Standard microtiter plates
3 pcs Deepwell plates
3 pcs VT15, VT54 or VT70 racks
1 pc R60 rack
or combinations

PAL System Tray Cooler for the storage of

3 pcs Standard microtiter plates
3 pcs Deepwell plates
3 pcs VT15, VT54 or VT70 racks
or combinations

• Under defined temperature conditions between 4 °C and 40 °C
• Depending on tray type inserts are required
• Including power supply and cables

Requires firmware version 3.1.21 or higher

Tray Holder and Sample Tray

• Temperature range between 4°C- 70°C
• For up to 32 vials of 10/20 ml
• External circulator bath for heating/cooling not included

For the storage of racks or plates at room temperature

allows to store samples with light sensitive compounds

For the storage of racks or plates under defined temperature conditions

temperature range between 4 °C and 40 °C

PAL System Valve Drive (without valve) for Valco Valves for applications like sample injection, column switching for online LC-LC/MS or online SPE-LC/MS, Multiplexing, column selection and many more.

Consisting of:

1 pc Valve Drive
1 pc PAL BusConnection cable

• Injection port bottom sensing minimizes carryover
• Constant force technology to reduce dead volume during Injection process
• UHPLC/HPLC: up to 50% faster switching times for optimum
• System performance and prolonged column life time
• Stackable design to reduce the space required
• Huge flexibility to arrange Multiple valve solutions
• The Fast Wash Module is also stackable below a Valve Drive

Requires firmware version 1.4.0 or higher